A one-piece jumpsuit in French terry with a lined hood on a cord, a full-length zipper, welt pockets at the front, and ribbed cuffs at the wrists and ankles.
The jumpsuit features a hood, cuffs at the bottom and on the sleeves, a zipper, and welt pockets in the front. The back has a middle seam and a gusset.
The hood is fully lined and carries a cord through eyelets, and the front opening is finished with facings that run from the neckline down along the zipper.
Fabric requirement, for fabric width 1.80 m (2 yd)
| Sizes | 40–42 S–M |
44–46 L–XLMOST PICKED |
48 XXL |
|---|---|---|---|
| Main fabric for height 180 cm / 70.9″ |
2.50 m 2 3/16 yd |
2.50 m 2 3/16 yd |
3.00 m 3 1/4 yd |
| Main fabric for height 186 cm / 73.2″ |
3.00 m 3 1/4 yd |
3.00 m 3 1/4 yd |
3.00 m 3 1/4 yd |
| Lining | 0.50 m 1/2 yd |
0.50 m 1/2 yd |
0.50 m 1/2 yd |
| Cuff | 0.20 m 7/32 yd |
0.20 m 7/32 yd |
0.20 m 7/32 yd |
Pattern pieces already include seam allowances. When purchasing fabric, please account for shrinkage and buy 5–10% more than required.
| Pattern piece | Pcs. |
|---|---|
| Main fabric | |
| 1 — Back | 2 |
| 2 — Front | 2 |
| 3 — Facing | 2 |
| 4 — Gusset | 1 |
| 5 — Sleeve | 2 |
| 6 — Neck facing | 1 |
| 7 — Hood | 2 |
| 8 — Outer pocket piece | 2 |
| 9 — Inner pocket piece | 2 |
| 10 — Pocket facing | 2 |
| Lining | |
| 11 — Hood | 2 |
| Ribbing | |
| 12 — Sleeve cuffs | 2 |
| 13 — Trouser cuffs | 2 |
Tap the diagram to zoom in
35 steps in seven stages, from the welt pockets to the final press.
Interface the location of the pocket on the inside of the front pieces, and mark the location of the pocket welts on the right side.
Press the pocket welt in half. Mark the allowances and control marks according to the pattern.
Mark the allowances and control marks on the pocket bag pieces from the inside according to the pattern.
Apply the welt pocket piece to the upper chalk line on the front piece and the pocket bag piece to the lower chalk line. Sew them with stitches along the control marks. Cut with scissors along the middle of the laid lines, not reaching the edge by 1 cm (3/8″), and at 45 degrees, not reaching 0.1 cm (1/16″) to the stitching lines.
On the pocket facing piece, mark allowances and control marks on the wrong side according to the pattern. Place the pieces right sides together and topstitch the pocket facing piece onto the stitching line for the welt pocket.
Turn the welt piece and the pocket bag piece inside out.
Sew the ends of the welt with a machine stitch.
Overlock the allowances on the wrong side of the pocket.
Topstitch along the front half piece below the stitching line for the welt by 0.1 cm (1/16″), so that the entrance to the pocket remains free.
Stitch and overlock the pocket bag with the pocket facing. Press.
Topstitch along the perimeter of the pocket, the ends and the entry line, by 0.1 cm (1/16″).
Overlock the middle cuts on the front pieces, fold the pieces face to face and sew. Press the seam allowances.
Interface the cuts under the zipper. Pin and sew the zipper into the middle seam on the front pieces along the notches. Place the zipper face to face with the fabric and 1 cm (3/8″) below the neck allowance. Cut the seam allowance at the end of the zipper and secure it with a stitch.
Fold the back pieces face to face and sew the middle seam on the overlocker. Press the seam allowances to the left side.
Pin and stitch the gusset piece to the back piece using an overlocker, placing the pieces face to face. Press the seam allowances onto the back piece.
Place the front piece onto the back piece, pin the shoulder seams and stitch using an overlocker. Press the seam allowances onto the back piece.
Place the main fabric hood pieces face to face and the jersey pieces face to face. Stitch the middle seams using an overlocker. Press the seam allowances in different directions.
Mark and baste the loops on the main fabric hood piece using the pattern.
Place one hood into the other face to face and stitch. Turn right side out and press the seam allowances.
Machine stitch along the seam, stepping back 2 cm (3/4″) from the edge, forming a drawstring casing for the cord.
Pin the hood into the jumpsuit neck and sew it in, folding the pieces face to face.
Place the facings on the neckline facing. Stitch and press the allowances.
Overlock the outer edge.
Fold the two front facing pieces together face to face and stitch a small section at the end.
Pin the neckline facing to the neck, and the front facing to the sewn-in zipper. Sew and turn inside out.
Topstitch along the zipper 0.5 cm (3/16″) from the stitching seam. Press.
Pin the sleeves into the open armhole face to face with the jumpsuit. Sew them in on an overlocker. Press the allowances towards the sleeve.
Pin the lower seam of the sleeve and the side seam. Sew them on an overlocker with one line. Press the seam towards the back piece.
Pin the inseam of the jumpsuit along the entire length and sew on an overlocker. Press the seam towards the back piece.
Fold the sleeve cuff and trouser cuff pieces in half and sew them into a ring using a machine stitch. Press the allowances.
Fold the cuffs in half lengthwise and press.
Pin the finished sleeve cuffs to the sleeves and the trouser cuffs to the trouser legs, face to face. Sew on an overlocker and press the seams towards the garment.
Cut the cord to the required length and thread it into the hood using a pin. Stitch the ends of the cord.
Fasten the neck facing with blind hand stitches along the shoulder and centre seam of the back piece, so that it does not bend back. Fasten the pocket bag to the facing with hand stitches.
Give the garment a final press.
